Thank you very much for your feedback on our products. We offer you the following instructions for setting up automatic kebab maker machines:

 

INTRODUCTION OF AUTOMATIC KEBAB MACHINES

Automatic kebab skewer machine model PS700H

TECHNICAL SPECIFICATIONS the amount of
MOTOR POWER(HP) 1.5
HYDRAULIC POMP SINGLE
SPEED(PER HOUR) 500
OIL TANK CAPACITY 17
USEFUL DURATION OF HYDRAULIC OIL FUNCTION 300 h
WEIGHT 120
DIMENSION 75*50*60

TECHNICAL SPECIFICATIONS the amount of
MOTOR POWER(HP) 4
HYDRAULIC POMP DOUBLE
SPEED(PER HOUR) 1500
OIL TANK CAPACITY 50
USEFUL DURATION OF HYDRAULIC OIL FUNCTION 3000h
WEIGHT 300
DIMENSION 140*60*115

kebab skewer machine PS700H
INTRODUCTION OF SWITCHBOARD AND HOW TO SET UP AUTOMATIC KEBAB SKEWER MACHINE

In this part we make you familiar with all parts of the switchboard of different models of kebab machines and the way of using the machine.

THE SWITCHBOARD OF AUTOMATIC KEBAB SKEWER MACHINE

 (DOUBLE MODEL)

THE SWITCHBOARD OF AUTOMATIC KEBAB SKEWER MACHINE

 (CABINET MODEL)

THE SWITCHBOARD OF AUTOMATIC KEBAB SKEWER MACHINE

 (TABLE-TYPE MODEL)

INTRODUCTION OF HYDRAULIC PART OF AUTOMATIC KEBAB SKEWER MACHINE

The hydraulic part is the part of pressure adjustment and oil tank of kebab machine. Before turning on the machine, first you should set this part.

TANK SECTION AND PRESSURE ADJUSTMENT PART OF AUTOMATIC KEBAB SKEWER MACHINE IN TABLE-TYPE AND CABINET MODE

TANK SECTION AND PRESSURE ADJUSTMENT PART OF AUTOMATIC KEBAB SKEWER MACHINE IN DOUBLE MODE

Safety tips

– Keep the machine in a safe place away from any contamination, dirt, smoke and chemicals.

– Place the machine on a smooth surface without slop.

– connect the machine to electricity without oscillation and secure. Be sure about earth wire.

Step by step instructions

1_Fill the oil tank according to the model of the machine and the amount stated in the instructions:

in table top models of kebab machines, the back door should be opened and oil should be poured into the tank by opening the door screws. In other models of kebab machines, pour the oil into the tank located at the bottom part of the machine to the specified location.

2_Grease the mold of the machines with eatable oil and repeat this after each wash to increase the mold longevity.

3_Pour the minced meat into the injection cylinder of the machine and then set the meat compartment on top of the cylinder and fill it with minced meat.

4_Switch on the main key of the machine to turn on the machine signal light.

5_ Switch on the main engine switch to turn on the electromotor.

6_ Turn the mold heaters on and wait for the molds to reach the specified temperature. The temperature is varied between 50 to 60c. The best temperature is 55 Centigrade degrees.  Adjust the distance of the sensors while the molds are in their lowest status. The distance between the two sensors should be 2 to 4 mm.

7_ Set the status key of the machine on manual. By the injection key make sure about the movement of the molds and injection jack. In this status the molds must be closed.

8_ By the air gauge on the oil tank, make sure about the operating pressure of the machine. The air gauge should be on 100 Bar

9_ Set the status key of the machine on automatic then put the skewer correctly in the mold, then the machine will start working automatically.

10_ If the meat is low on the skewer, increase the injection timer and reduce the timer if the meat is high.

INJECTION TIMER

11_ After doing the process of skewering by the machine, take out the kebab skewer and put the next ones.

INJECTION PARTS OF KEBAB MACHINE:

CLOSE THE INJECTION PARTS OF KEBAB MACHINE CORRECTIY

First put the injection hopper into the nut, then put the coil, injection gasket and finally the injection grating gasket. Then put these injection parts on the injection piston and it into the injection cylinder and fasten the nut tightly. As the skewering finished, open and clean the injection parts.

As the skewering finished, open and clean the injection parts.

Instructions of obviation of technical problems of automatic kebab machines

PROBLEM

REASON OF PROBLEM

HOW TO SOLVE THE PROBLEM

The mold don’t warm up

1. Temperature of thermostat is not set
2. The elements of molds have problem
3. The problem is with relays

1. The temperature of thermostat should be on 55 degree centigrade
2. The elements should be replaced
3. The relays should be displaced, otherwise they should be replaced

the injection of meat doesn’t accomplish completely

1.The injection timer is not set
2.The mold has been obstructed
3.The injection parts are not closed in right order and correctly
4.The hydraulic pressure is low

.Increase the injection timer
2.Clean the mold then put the skewer on it
3.Open the injection parts and close them in order
4.Switch the handle under the hydraulic valve in hand order

as the injection accomplish, meat come out of mold

1. The injection timer is not set
2. The tape around the mold is decayed

1.Decrease the injection timer
2.Change the tape of mold

meat stick to the mold

1. The cover of mold is decayed
2. The mold doesn’t warm up

1. The mold should be covered again
2.Increase the temperature of thermostat

The machine is not work in Automatic mode

1. The status key is not in automatic mode
2. The sensor of skewer is not set
3. The relays have problem

1.Set the status key in Automatic mode
2.The sensor of skewer should set on the height of 2 or 4 millimeter between sensor and skewer
3.The relays should be displaced, otherwise they should be replaced

Caution:

  • NEVER WASH THE KEBAB MACHINE WITH WATER